| No
|
Deliverable title
|
Disse-mina-tion level
|
Document
|
| D-general | Final SP 1 report | PU |
D-general
|
| D1.1.1A | Status review IHRA test procedures (task 1.1.1) | PU |
D1.1.1A
|
| D1.1.1B | Validated side impact barrier test procedure with revised barrier (including demonstrator revised MDB barrier) (Task 1.1.1) | PU |
D1.1.1B
|
| D1.1.1C-part 1 | Assessment of protection offered to small population with use of WorldSID 5F | PU |
D1.1.1C-part 1
|
| D1.1.1C-part 2 | Assessment of protection offered to small population with use of WorldSID 5F | PU |
D1.1.1C-part 2
|
| D1.1.2A | A validated side impact pole test procedure (Task 1.1.2) | PU |
D1.1.2A
|
| D1.1.2B | Cost-benefit for regulatory pole test including effect of defensive active systems | PU |
D1.1.2B
|
| D1.1.3A | First assessment of extended interior head-form test procedure (Task 1.1.3) | PU |
D1.1.3A
|
| D1.1.4 | Recommendation on feasibility of OOP test procedure for Europe (Task 1.1.4) | PU |
D1.1.4
|
| D1.1.5A | Methodology to address to address non struck side injuries (Task 1.1.5) | PU |
D1.1.5A
|
| D1.1.5B | Report on main influencing factors in side impact compatibility, effect of changes for frontal impact compatibility and concepts for a side impact compatibility test (Task 1.1.5) | PU |
D1.1.5B
|
| D1.2.1 | Draft test and assessment protocol for AE-FW test | PU |
D1.2.1
|
| D1.2.2 | Evaluated final AE-FW test and assessment protocol | PU |
D1.2.2
|
| D1.2.3A | Accident analysis report for specification of AE-FW test (Task 1.2.3) | PU |
D1.2.3A
|
| D1.2.3B | Final AE-FW cost-benefit analysis | PU |
D1.2.3B
|
| D1.3.1 | Report on implications for regulations, and a report on recommendations for test and evaluation methods of adaptive safety systems and remote sensing systems (Task 1.3.1) | PU |
D1.3.1
|
| D1.3.2 | Report describing the proposed evaluation methodology for adaptive safety systems and remote sensing systems (Task 1.3.2) | PU |
D1.3.2
|
| D1.3.3 | Detailed draft test scenarios for the specific pre-crash safety system | PU |
D1.3.3
|
| D1.3.4 | Evaluated assessment procedure for a frontal pre-crash safety system | PU |
D1.3.4
|
| D1.3.5 | Final evaluation methodology for advanced safety systems | PU |
D1.3.5
|
| No
|
Deliverable title
|
Disse-mina-tion level
|
Document
|
| D-general | Final SP 2 report | PU |
D-general
|
| D2.1.1A | Generalised geometric corridors and contact characteristics (Aggressivity Index) of the typical heavy vehicle fleet (Task 2.1.1) | PU |
D2.1.1A
|
| D2.1.1B | Impact situations and pedestrian/cyclist kinematics based on real world accident scenarios (Task 2.1.1) | PU |
D2.1.1B
|
| D2.1.2A and 2,1,2B | Development strategies for enhanced pedestrian and cyclist friendly design (including front and side structures) including overrun prevention system for a new Heavy vehicle concept based on the existing standards defined in 89/297/EWG. (Task 2.1.2) and Suggestions for design changes by means of add on parts for existing HV designs (special topic on HV from CEE countries) for front and side structures. (Task 2.1.2) | PU |
D2.1.2A and 2,1,2B
|
| D2.1.3 | Demonstrator module for new design concepts | PU |
D2.1.3
|
| D2.1.4 | Guidelines for assessment criteria for HV passive safety test methods | PU |
D2.1.4
|
| D2.1.5 | System description of the experimental safety module | PU |
D2.1.5
|
| D2.1.6 AB | Demonstration of truck front design improvements for vulnerable road users focusing on structural interaction/Demonstration of truck front design improvement for vulnerable road users focusing on run-over prevention | PU |
D2.1.6 AB
|
| D2.1.7 | Guidelines for integrated design and evaluation of advanced vulnerable road user protection systems | PU |
D2.1.7
|
| D2.2.0 | Assessment of the potential safety benefit of truck/trailer side protection | PU |
D2.2.0
|
| D2.2.1 B | Impact situations and occupant kinematics based on real world accident scenarios | PU |
D2.2.1 B
|
| D2.2.2 A and D2,2,2B | Draft Development strategies for enhanced car impact protection design (including truck and trailer) for new heavy vehicle concepts based on existing standards and Draft Suggestions for design changes by means of add on parts for existing heavy vehicle designs (special topic on HV from CEE countries) for side structures | PU |
D2.2.2 A and D2,2,2B
|
| D2.2.2C | Report on new designs considering newest technologies including a cost benefit analysis | PU |
D2.2.2C
|
| D2.2.3A | Intermediate report on experimental design studies | PU |
D2.2.3A
|
| D2.2.3B | Report on assessment procedures and prototyping for advanced design of heavy vehicle side structure | | not available |
| D2.2.4 | Demonstration of truck side design improvements | PU |
D2.2.4
|
| D2.2.5 | Guideline on development, integration and certification of enhanced opponent vehicle occupant protection systems | PU |
D2.2.5
|
| No
|
Deliverable title
|
Disse-mina-tion level
|
Document
|
| D-general | Final SP 3 report | PU |
D-general
|
| D3.1.1 | Definition of vehicle and pedestrian/cyclist impact conditions for use as input to later computer simulations (Task 3.1.1) | PU |
D3.1.1
|
| D3.1.2A | The generalised geometry corridors, generic shapes and sizes of the vehicle fleet covering cars, MPV’s and SUV’s | PU |
D3.1.2A
|
| D3.1.2B | Contact characteristics of the vehicle fleet covering cars, MPV’s and SUV’s | PU |
D3.1.2B
|
| D3.1.3 | Analysis of the in-depth databse of reqal-world pedestrian and cyclists accident cases | PU |
D3.1.3
|
| D3.2.3 | Impact conditions for each group of pedestrians and cyclists with the defined vehicle types | PU |
D3.2.3
|
| D3.2.4 | Assessment describing relevance of secondary ground impact and its influence on injuries | PU |
D3.2.4
|
| D3.3.1 | no title | |
D3.3.1
|
| D3.3.2A | Review of basis for separate sub-system tests | PU |
D3.3.2A
|
| D3.3.2B | Review of the current pedestrian lower and upper leg procedures | PU |
D3.3.2B
|
| D3.3.2C | Review of current child and adult pedestrian head impact test procedures | PU |
D3.3.2C
|
| D3.3.2D | Identification of gaps in the current impactor test procedures relating to pedestrians and cyclists | PU |
D3.3.2D
|
| D3.3.3 A | Initial concepts for new or improved test procedures | PU | not available |
| D3.3.3B | New or improved test methods to address lower and upper leg impacts | PU | not available |
| D3.3.3C | New or improved test methods to address child and adult head impacts | PU | not available |
| D3.3.3D | Concept for a hybrid test Procedure | PU | not available |
| D3.3.3E | Additional/alternative test methods for cyclists | PU |
D3.3.3E
|
| D3.3.3F | Test procedures for the new or improved test methods | PU |
D3.3.3F
|
| D3.3.3G | Safety assessments of the new and improved test methods for the protection of vulnerable road users | PU |
D3.3.3G
|
| D3.3.3 H | Evaluation of the extended scope for Flex PLI obtained by adding an upper body mass | PU |
D3.3.3 H
|
| No
|
Deliverable title
|
Disse-mina-tion level
|
Document
|
| D-general | Final SP 4 report | PU |
D-general
|
| D4.1.1 | Common accident data-set. | PU |
D4.1.1
|
| D4.1.4 | Report on the performance of riders’ protective devices (helmets, protective clothing, impact protectors…) and the corresponding injuries of riders (task 4.1.4). State-of-the-art regarding motorcyclists’ helmets and clothing (task 4.1.5). Future research guidelines. | PU |
D4.1.4
|
| D4.2.1 A | Accident reconstruction. Methodology and scenario. | PU |
D4.2.1 A
|
| D4.2.2 | Motorcyclists against road infrastructure: Injury mechanisms | PU |
D4.2.2
|
| D4.2.3 B | Estimation of the benefit of introducing motorcyclists protective infrastructure in European Roads | PU |
D4.2.3 B
|
| D4.2.4A | Design recommendations for the development of new road motorcyclists protective device (MPD) | |
D4.2.4A
|
| D4.2.4 B | Rating of the new MPD and already existing systems | PU | not available |
| D4.3.1A | Optimisation methodologies to improve existing protective equipment. Analysis from in-depth data studies and simulated reconstructions. | PU |
D4.3.1A
|
| D4.3.1B | Data on vehicle motion and impact: definition of working and activation parameters of the safety system. | PU |
D4.3.1B
|
| D4.3.2 D | Prototype validated helmet model (CIDAUT) | PU |
D4.3.2 D
|
| D4.3.2E | Numerical evaluation of the helmet prototype against improved head injury criteria | PU |
D4.3.2E
|
| D4.3.3 A | Female thorax protector | PU |
D4.3.3 A
|
| D4.3.3 B | Different female and male thorax protector size | PU |
D4.3.3 B
|
| D4.3.3 C | Demonstration of the implementation of thorax protector in existing garments | PU |
D4.3.3 C
|
| D4.3.4C | Proposal of road and misuse tests standard for the development of passive safety systems in the motorcycle industry | PU |
D4.3.4C
|
| D4.3.4D | Final definition of activation strategies of an innovative passive safety system | PU |
D4.3.4D
|
| No
|
Deliverable title
|
Disse-mina-tion level
|
Document
|
| D-general | Final SP 5 report | PU |
D-general
|
| D5.1.1B | Report on head injury criteria for specific injury mechanisms | PU |
D5.1.1B
|
| D5.1.1D | New head injury mechanisms | PU |
D5.1.1D
|
| D5.1.2 B | Report detailing the chosen statistical method(s) and scaling techniques (Task 5.1.2) | PU |
D5.1.2 B
|
| D5.1.2 B | Report detailing the chosen statistical method(s) and scaling techniques (Task 5.1.2) | PU |
D5.1.2 B
|
| D5.1.2C | Software package to implement scaling techniques (Task 5.1.2) | PU |
D5.1.2C
|
| D5.1.4 AA, AB AC | Review of the thorax and abdomen injury criteria (Task 5.1.4) | PU |
D5.1.4 AA, AB AC
|
| D5.1.4 AA | Review of the thorax and abdomen injury criteria (Task 5.1.4) | |
D5.1.4 AA
|
| D5.1.4 AB | Review of the thorax and abdomen injury criteria (Task 5.1.4) | |
D5.1.4 AB
|
| D5.1.4 AC | Review of the thorax and abdomen injury criteria (Task 5.1.4) | |
D5.1.4 AC
|
| D5.1.4 D | Material properties of soft tissues: experimental data | PU |
D5.1.4 D
|
| D5.1.4 F | Thoracic injury risk curves for the THOR 50th percentile dummy | | not available |
| D5.2.5 | 5th percentile female side impact dummy head & neck response requirements in NBDL and Patrick and Chou test conditions | PU |
D5.2.5
|
| D5.2.8 | Single rib and 2D rib deflection sensor drop table impact tests; sensitivity to impact load and impact direction | PU |
D5.2.8
|
| D5.2.9 | Updated prototype evaluation of biofidelity, sensitivity and durability, including calculation of ISO/TR9790 biofidelity rating of the updated prototype dummy | PU | not available |
| D5.2.10 | Draft WorldSID 5th female certification corridors for head, neck, shoulder, thorax, abdomen and pelvis | PU |
D5.2.10
|
| D5.2.11 | WorldSID Small female Side Impact Injury Risk Functions for Thorax, Abdomen and Pelvis based on dummy biomechanical testing and existing injury data | PU | not available |
| D5.2.12 | Evaluation of the small female side impact dummy in current and future side impact test procedures (Advanced European Mobile Deformable Barrier Test Procedure) | PU |
D5.2.12
|
| D5.2.13 | Evaluation of injury prediction capability of the dummy with developed injury reference values in two accident reconstruction cases | PU |
D5.2.13
|
| D5.3.3/D534 | Report on implementation and validation of injury criteria in models | PU |
D5.3.3/D534
|
| D5.3.5 & 5.3.5.A | Report on material models for damage and failure of human tissues | PU |
D5.3.5 & 5.3.5.A
|
| D5.3.5 & 5.3.5.A | Report on material models for damage and failure of human tissues | PU |
D5.3.5 & 5.3.5.A
|
| D5.3.5 & 5.3.5.A | Report on material models for damage and failure of human tissues | PU |
D5.3.5 & 5.3.5.A
|
| D5.3.8 | Parametric posture prediction module | PU |
D5.3.8
|
| D5.3.9/D.5.3.13 | Muscle active behaviour models and implementations in crash codes | PU |
D5.3.9/D.5.3.13
|
| D5.3.15 | Head Injury risk curves for adults and elderly | PU |
D5.3.15
|
| D5.3.17 | Simulation of a car occupant lateral accident with an active human model (non-struck side) | PU |
D5.3.17
|
| D5.3.24 & 25 | A virtual testing demonstrator of using human models in virtual testing of pedestrian impact | PU |
D5.3.24 & 25
|
| D5.3.26 & 27 | New head structure constitutive laws implemented in Radioss, LsDyna, PamCrash and Madymo and report of the validation in these four codes | PU |
D5.3.26 & 27
|
| No
|
Deliverable title
|
Disse-mina-tion level
|
Document
|
| D-general | Final SP 7 report | PU |
D-general
|
| D7.1.1 | Validated dummies for the use of SP2, SP4 and SP7 | |
D7.1.1
|
| D7.1.2 | Second generation, industrial OOP airbag simulation (Task 7.1.2) | PU |
D7.1.2
|
| D7.1.3A | New barrier models for side impact (Task 7.1.3) | |
D7.1.3A
|
| D7.2.2 C | Design robustness optimization | PU | not available |
| D7.2.3B | Workshop on Virtual Testing methods and applications (T7.2.3, M20) | | not available |
| D7.3.1 A | Report on ADVISER extensions (M30) | PU | not available |
| D7.4.1 - D7.4.3 | Part B of road map integrating aspects developed in DIP4 work. | | not available |
| D7.4.5 | Final recommendations report for the future of virtual testing | PU |
D7.4.5
|